- 5207 silent knight manual
Looking for:
5207 silent knight manual. Silent Knight 5207spec |
Silent Knight SK Programming.
5207 silent knight manual
SILENT KNIGHT INSTALLATION, PROGRAMMING, AND OPERATION MANUAL Pdf Download | ManualsLib.
Hide thumbs Also See for : Operator's manual 4 pages. Table Of Contents. Quick Links. Table of Contents. Knitht Page. Next Page. Troubleshooting Troubleshooting 84 Troubleshooting and System Messages Page 2: Table Of Contents 3.
Page 4 Section 8 Reporting Page 6: Introduction Section 1 Introduction The Model is an 8-zone fire alarm control panel expandable up to 16 zones with a dig- ital communicator that meets NFPA 72 requirements. The cabinet can be surface mounted or semi-flush mounted.
Page 7: Optional Accessories For remote annunciation of alarm and trouble Module status information for each zone. Page 8: Agency Listings And Requirements 4. If the causes harm to the telephone network, the telephone company will notify the user in advance that 5207 silent knight manual discontinuance of service may be required. When advance notice is not practical, the telephone company 5207 silent knight manual notify the user as soon as possible. Users have the right to file complaints, if necessary, with the Federal Communications Commission.
If the and its accessories are to be used as part of a UL installation, carefully read the UL requirements in this section. The following applicable NFPA 72 standards can 5207 silent knight manual Follow the current load restrictions shown in 5207 silent knight manual 3. Induced noise can interfere with telephone communication or even cause false alarms. Avoid pulling one multiconductor cable for the knitht panel. Figure Model Wiring Reference Refer to Table for available battery sizes and the maximum standby current load each can support.
Figure is an разделяю adobe acrobat x pro tutorial youtube free download клевая of a completed worksheet. Measure the alarm current. If knihgt one current rating is listed, the draw for that device is the same whether the system is in alarm or standby condition. Ensure that the total 5207 silent knight manual of all items attached to the5207 silent knight manual the itself, does not exceed 5 A when the panel is in alarm see Section 3.
Page Power Supply Wiring Model power supply. Do NOT apply power knught this panel until all accessories are properly connected. In all cases, the authority having jurisdiction takes pre- cedence. 5207 silent knight manual cabinet outside dimensions are: Table on onight next page lists the function and khight rating of each terminal. See Section 3. Notification device output 2 Positive Notification device output amnual Negative 1 amp max. Page Telephone Line Connection A situation could occur where both phone lines appear to silejt good, but the dialer 5207 silent knight manual get through to the central station on the first line.
In this case, the will switch phone lines and attempt the call again 5207 silent knight manual the second line. Make sure the phone lines are programmed properly see Section 7. Model P2 5207 silent knight manual the zone expander to the Quick Connect P3 For temporarily connecting a for programming or troubleshooting. Requires cable assembly not included.
Page Compatible Product Installation Each class Вот ссылка zone is a four-wire circuit that allows an alarm to be detected even after a single open or ground fault occurs. When a single open or ground fault occurs, the audible trouble signal will sound and the will report the trouble to the central station if programmed to report troubles. Page Class B Style A Zones The detection of an open will cause the audible trouble signal to sound and the will report the trouble to the central station if programmed to do so.
Figure shows how to wire a class B style A loop. One side of each class B loop connects to a zone input terminal and the other side of each loop connects to loop power. Model Status Display Module The Model Status Display module provides remote annunciation of alarm and trouble status information for each zone. Make sure power is OFF at maanual panel before plugging in the Maintain a physical separation of one-half inch or more between field wires and connection points to prevent damage from transients.
To install, fit the bracket over the power supply нажмите сюда in the cabinet. With panel power OFF, use the cable provided to connect the to its connector P2 on the Insert screws provided.
Place the four plastic stand- offs into the bracket and snap onto the PC board. Page Model Direct Connect Module The maximum coil and 5207 silent knight manual resistance combined must not exceed 30 ohms. To install the for city box connection: 1. Locate the knockout on the right side of the cabinet to connect the using a short piece of conduit must not exceed 20 feet in length.
Page Nfpa 72 Polarity Reversal To install the for polarity reversal, follow the steps below: 1. Refer to the installation sheet shipped with the 95M for complete information. Note: The is not available from Silent Knight. It also provides knitht and alarm information and can be used for programming.
When the annunciator powers up, it will dis- play its ID code and current status of the panel. A temporary can be connected for 5207 silent knight manual and troubleshooting. See Section 4. Page Model Signal Power Expander The Model is a notification and auxiliary power expander that provides up to 6. Figure shows you how to connect the Model to the Model panel. Page Model Zone Converter 4.
Figure and Figure show 5207 silent knight manual to make conversions. Page Supervised Notification Appliance Outputs Figure shows how to connect the notification circuits to the Contact Silent Knight if you have any questions about 5207 silent knight manual notification circuits. Page Auxiliary Relays loss of AC, low battery, failed to communicate, phone line troubles, and notification circuit troubles.
Refer to the programming manual for more 5207 silent knight manual. Figure shows the relay contact connections using a doorstrike application as an example. Page Operation Section 5 Sillent To operate the you can use either the built-in touchpad or the Model Remote Annunciator.
Note that if no keys are pressed for 5207 silent knight manual minutes while in program mode, the system will time out and resume normal operation. For complete information silet 5207 silent knight manual display messages, see Section 9. Table Built-in Touchpad Display Codes Page Led Indicators Operation 5.
The chart below explains the meaning of these LEDs. In walk test mode, the built-in self test on the ESL series smoke /36021.txt may be unreliable. If the built-in self test is required, it should be done in the normal operating mode with the zone speed set to 3 seconds or higher.
Please read Section 7 thoroughly, especially if you have never programmed the before. The quick reference chart can be used for keeping track of how options have been pro- grammed for an installation. You must be in Step Programming Mode also known as mode 27 to program the panel. See the following sections for 5207 silent knight manual. Using Step Programming The digits appear on the right side of the display and scroll to the left as you continue to enter data.
The way you move through Mode 27 may also vary from how it is described here. Enable the printer if your installation includes a printer in- terface. The is not UL listed for use with the Enables 24V power. Do NOT disable. These digits are reserved by the manufacturer for future use. Page Step 3.
More System Options 5207 silent knight manual Description Step 3 allows you to select seven system options shown below. To adobe pro cs6 ebay an option, press its number. If you select this option, bells will 5207 silent knight manual in the pattern shown below for customizing patterns, refer to Steps 27 and 28 : 3.
Page Step 5. Miscellaneous Options Display Description Step 5 is for programming several system options, including bell supervision. Select this option if you want knifht tests reported to the central station. Page 60 Note: This very fast response time can increase the possibility of false alarms, since transients and other interference can set off alarm conditions in such a short time span.
Comments
Post a Comment